Custom remap on the dyno
Motorcycle ECU remap in Phuket
We rewrite the map inside your bike’s own ECU, against measurements taken from your bike on the dyno. No add-on box, nothing copied from another machine, and your original file is kept so it can all be undone.
What an ECU remap is
The engine control unit decides how much fuel to inject and when to fire the spark, thousands of times a minute, by looking values up in tables. A remap, also called flash tuning or an ECU flash, reads those tables out, corrects them and writes them back. The hardware on the bike does not change.
The factory tables are a compromise written to pass emissions and noise tests everywhere the model is sold. They are lean where the test looks, and they take no account of the exhaust you fitted last month.
Custom map or downloaded file
A file bought online was written for somebody else’s bike, exhaust, fuel and climate. It may be better than stock; nobody knows until it is measured.
A custom map starts from a baseline dyno run of your bike as it stands. The air/fuel trace shows where it is lean or rich, those cells are corrected, and the bike is run again. That loop repeats until the trace sits in the target band from low revs to the limiter, at part throttle as well as wide open.
What can be changed
Which of these apply depends on the ECU in your bike. We tell you before you book.
- Fuel maps
- How much fuel is injected at every combination of revs and throttle. The core of the job, corrected against the measured air/fuel ratio.
- Ignition timing
- When the spark fires. Adjusted with care and only where the engine and the fuel allow it.
- Throttle maps
- On ride-by-wire bikes, how far the butterflies open for a given twist of the grip. This is where a snatchy throttle is cured.
- Deceleration fuel cut
- The abrupt fuel cut on a closed throttle that makes the bike lurch when you reopen it.
- Limiters
- Rev limiter, top-speed limiter and gear-dependent restrictions, for bikes used where that is appropriate.
- Fan temperature
- The coolant temperature at which the radiator fan starts. Earlier is kinder in Phuket traffic.
- Exhaust-related fault codes
- Warning lights caused by a removed exhaust valve servo or oxygen sensor after an exhaust change.
- Quickshifter and race functions
- On supported models: quickshifter, launch control, pit limiter. Some need an extra harness or sensor.
How a tuning day runs
Nothing is written to the ECU before the baseline is measured.
-
01 / 06
You send the bike’s details
Make, model, year and what is fitted. We check the ECU against the tools and tell you whether it is done through the diagnostic plug or on the bench.
-
02 / 06
Check-in
Chain, rear tyre, leaks and stored fault codes. Anything that would spoil the numbers or endanger the bike is dealt with first.
-
03 / 06
Baseline runs
The bike goes on the rollers as it arrived. Power, torque and air/fuel ratio are recorded so there is something honest to compare with.
-
04 / 06
Stock file saved
The original contents of the ECU are read and archived. From here on everything can be undone.
-
05 / 06
Mapping
Fuel is corrected against the measured air/fuel ratio across revs and throttle positions. Ignition, throttle maps and the agreed settings follow, where the ECU allows it.
-
06 / 06
Verification runs
The new map is run again until the trace sits where it should. You get the before-and-after sheet and we walk you through it.
What to expect, honestly
- A stock modern bike gains little at the peak. The difference is in the mid-range, the throttle response and the way it pulls from low revs.
- A bike with a full exhaust on a stock map gains the most, because its map is the furthest from right.
- A remap does not fix a mechanical problem. Worn injectors, an air leak or a slipping clutch show up on the dyno and have to be repaired first.
- Fuel consumption usually stays close to what it was. Richer where the engine was lean, no change where it was fine.
Reversible, and what that means for warranty
Your original file is read before anything is written and stays in our archive. It can be flashed back whenever you want: before selling the bike, or before a dealer visit.
A manufacturer may still refuse a warranty claim on an engine whose ECU has been modified. If the bike is under warranty, weigh that before you decide.
Changed parts later?
A map fits the hardware it was written for. Change the exhaust, the air filter or the gearing and the fuelling moves again. A retune starts from your last file, which makes it quicker than a first map.
Already running a piggyback box?
Power Commander, Rapid Bike and similar units sit between the ECU and the injectors and bend the signal. They cannot change ignition limits, throttle maps, limiters or fan settings. In most cases we recommend mapping the ECU itself and taking the box off. Tell us what is fitted.
Bikes we remap
ECU remap by make
-
Honda
Woolich Racing · Alientech KESS3
CB500F / CBR500R / NX500, Rebel 500, CB650R / CBR650R…
-
Yamaha
Woolich Racing · Alientech KESS3
MT-03 / YZF-R3, MT-07 / XSR700, Ténéré 700…
-
Kawasaki
Woolich Racing · Alientech KESS3
Ninja 400 / Z400, Z650 / Ninja 650, Versys 650…
-
Suzuki
Woolich Racing · Alientech KESS3
V-Strom 650, V-Strom 800 / 1050, SV650…
-
BMW
Alientech KESS3 · Woolich Racing
G 310 R / GS, F 750 / 850 / 900 GS, R 1250 GS / GSA…
-
Ducati
Alientech KESS3 · Woolich Racing
Scrambler, Monster, Hypermotard…
-
Triumph
Alientech KESS3
Speed 400 / Scrambler 400 X, Trident 660 / Tiger Sport 660, Street Triple…
-
KTM & Husqvarna
Alientech KESS3
390 Duke / Adventure, 790 / 890 Duke, 790 / 890 Adventure…
ECU remap questions
What does an ECU remap actually change?
It rewrites the tables inside your bike’s own ECU: how much fuel is injected, when the spark fires, how the throttle butterflies follow your wrist, and settings such as rev limiters and fan temperature. No extra box is added to the bike.
How much power will I gain?
It depends on the bike and what has been done to it. A stock modern bike usually gains little at the peak and noticeably more in the mid-range and in throttle smoothness. A bike with a full exhaust on its stock map gains the most, because the map is the furthest from right. We show you the baseline before any work, so you see the real difference on paper.
Is the remap reversible?
Yes. Before changing anything we read your original ECU file and keep it. It can be written back at any time — before a sale or a dealer visit.
What is the difference between a custom map and a downloaded one?
A downloaded map was written for someone else’s bike, exhaust, fuel and climate. A custom map is corrected against air/fuel readings from your bike on the dyno, cell by cell, and then checked with further runs.
I already have a Power Commander or Rapid Bike. Can you work with it?
Tell us what is fitted. In most cases we recommend mapping the stock ECU directly and removing the piggyback, because the ECU can change ignition, limiters and throttle maps that an add-on box cannot reach.
Will a remap affect my warranty?
It can. A manufacturer may refuse a warranty claim on an engine whose ECU has been modified. We keep your original file so the bike can be returned to stock, but you should decide with that in mind.
Can you switch on a quickshifter or remove a speed limiter?
On many models, yes — it depends on the ECU. Some bikes need an additional harness or sensor for a quickshifter. Tell us the model and year and what you want, and we check before you come.
I changed the exhaust after you mapped the bike. What now?
Come back for a retune. We start from your last map, measure with the new parts and correct it, which is quicker than a first map.
Booking
Send us the bike, the year and what is fitted.
We check that your ECU is supported, tell you which tool it needs and what it costs, then give you a slot.