Skip to content
Phuket Dyno by Phuket Garage

Dyno power run

Motorcycle dyno test in Phuket

Three full-throttle pulls on the rollers and you know what the bike makes at the rear wheel, where the torque is, and whether its fuelling is healthy. No ECU work, no commitment.

What a dyno run tells you

A chassis dyno: the rear wheel turns a heavy roller, and from how fast the roller accelerates we calculate the power reaching the tyre. A sensor in the exhaust records the air/fuel ratio at the same time.

  • Power and torque at the wheel, across the whole rev range and not just at the peak.
  • Air/fuel ratio at every point of the pull. This is the trace that shows whether the engine is running lean, rich or right.
  • Flat spots and dips you feel on the road, drawn as a line you can point at.
  • A printed and PDF sheet to keep, to compare with later, or to show a buyer.

When a run is worth booking

  • After fitting an exhaust or filter, to find out whether the bike needs a remap or copes as it is.
  • Before buying a used bike. A healthy engine makes the power it should; a tired or badly modified one shows it.
  • Before and after other work, such as a valve service or new injectors, to see what changed.
  • Chasing a problem that only appears at high load: a misfire at the top end, a hesitation at one rev range.
  • Curiosity. Plenty of riders just want to know.

What happens during the hour

The bike is checked over, strapped down by the front wheel and warmed to operating temperature with fans blowing through the radiator. Each pull runs through the revs in a high gear at full throttle. We do three, so one odd reading does not decide the result, and print the best consistent run.

Bikes with traction control or ABS sometimes object to a rear wheel spinning while the front stands still. We know which models need dyno mode or a workaround, so tell us the model and year when you book.

Reading the number honestly

The brochure figure is measured at the crankshaft. The dyno measures at the tyre, after the gearbox, chain and tyre have taken their share, so the number is lower, typically by ten to fifteen percent. Air temperature and humidity move it too, and Phuket has plenty of both.

A figure from one dyno is not comparable with a figure from another. What a dyno is good for is comparing your bike with itself: before and after, on the same rollers, on the same day. That is exactly what a custom remap relies on.

Before you come

Six things we check before the first pull

  • Chain and sprockets

    Adjusted, lubricated, not worn out. A tired chain can let go at full power.

  • Rear tyre

    Good tread, correct pressure, no cuts. A road tyre grips the roller far better than a knobbly.

  • No leaks

    Oil, coolant or fuel on the rollers ends the session.

  • Your usual fuel

    At least half a tank of what you normally buy. The map is written for it.

  • Faults fixed first

    A misfire or a warning light is a repair, not a tuning job. Tell us and the workshop looks first.

  • Final parts fitted

    Exhaust, baffle and air filter as you will ride it. Change them later and the map is off again.

Dyno test questions

Where can I dyno a motorcycle in Phuket?

At the Phuket Garage workshop in Kamala (41/11 Soi The Bell, Moo 5). Dyno runs and ECU tuning are by appointment, every day between 08:00 and 20:00. Message us on WhatsApp with your bike and we give you a slot.

I only fitted a slip-on. Do I need a remap?

Not always. Some bikes cope with a slip-on, others run lean in the mid-range. A dyno run with the air/fuel ratio recorded answers the question in an hour, and you only pay for mapping if the sheet shows it is needed.

Which fuel should I bring the bike on?

The fuel you normally use — gasohol 95, 91 or E20 — with at least half a tank. The map is written for what is in the tank, so do not fill up with something special for the day.

What is the difference between wheel horsepower and the figure in the brochure?

The brochure quotes power at the crankshaft. The dyno measures it at the rear tyre, after the gearbox, chain and tyre have taken their share, so the number is lower — typically by ten to fifteen percent. Heat and humidity move it too. What matters is the comparison between your own before and after runs on the same day.

How should I prepare the bike?

Chain adjusted and lubricated, rear tyre in good condition and at the correct pressure, no oil or coolant leaks, fresh enough oil, and any known faults fixed first. If something needs attention, the workshop next to the dyno can do it before the run.

Do I need to leave the bike with you?

For a power run you can wait. For a remap plan to leave it for the day. Bench work, where the ECU comes off the bike, can run into a second day.

Booking

Send us the bike, the year and what is fitted.

We check that your ECU is supported, tell you which tool it needs and what it costs, then give you a slot.

WhatsApp +66 80 681 6753 LINE @phuketgarage

Daily 08:00–20:00, by appointment

Book a dyno slot