Honda · Woolich Racing · Alientech KESS3
Honda ECU remap & dyno tuning in Phuket
Thailand builds and rides more Hondas than anything else, and most of the big ones leave the factory fuelled lean at part throttle to pass emissions tests. Add a slip-on and the map is further off than it was.
What Honda riders come in about
Hesitation low in the revs
The 500 twins and the 650 fours are commonly reported to stumble just off idle and at small throttle openings. That is fuelling, and it is measurable on the dyno before we touch anything.
Aftermarket exhausts
A freer exhaust on a stock Honda map usually reads lean through the mid-range. We map fuel against the measured air/fuel ratio rather than loading a generic file.
Adventure bikes in the heat
Africa Twin and Transalp owners often ask for the radiator fan to start earlier for slow traffic and hill climbs. Where the ECU exposes the setting, it is a small change.
Models we see most
- Honda CB500F / CBR500R / NX500
- Honda Rebel 500
- Honda CB650R / CBR650R
- Honda CRF300L / Rally
- Honda XL750 Transalp
- Honda CRF1100L Africa Twin
- Honda CBR1000RR
The list is a guide, not a promise. ECU support changes with the model year. Send us yours and we check it before you ride over.
How we get into a Honda ECU
Many Honda ECUs are mapped with Woolich Racing. Newer Keihin units that Woolich does not cover are read on the bench with KESS3.
About Woolich Racing · About Alientech KESS3
Whichever tool reads it, the map is written the same way: a baseline dyno run, your stock file saved, fuelling corrected against the measured air/fuel ratio, then verification runs. The full method is on the ECU remap page.
How a tuning day runs
From your message to the before-and-after sheet
-
01 / 06
You send the bike’s details
Make, model, year and what is fitted. We check the ECU against the tools and tell you whether it is done through the diagnostic plug or on the bench.
-
02 / 06
Check-in
Chain, rear tyre, leaks and stored fault codes. Anything that would spoil the numbers or endanger the bike is dealt with first.
-
03 / 06
Baseline runs
The bike goes on the rollers as it arrived. Power, torque and air/fuel ratio are recorded so there is something honest to compare with.
-
04 / 06
Stock file saved
The original contents of the ECU are read and archived. From here on everything can be undone.
-
05 / 06
Mapping
Fuel is corrected against the measured air/fuel ratio across revs and throttle positions. Ignition, throttle maps and the agreed settings follow, where the ECU allows it.
-
06 / 06
Verification runs
The new map is run again until the trace sits where it should. You get the before-and-after sheet and we walk you through it.
Honda tuning questions
Can you remap my Honda in Phuket?
Most fuel-injected Honda models can be remapped at our workshop in Kamala, using Woolich Racing and Alientech KESS3. Support depends on the model year and the ECU fitted, so send us make, model and year and we confirm before you book.
How much power will I gain?
It depends on the bike and what has been done to it. A stock modern bike usually gains little at the peak and noticeably more in the mid-range and in throttle smoothness. A bike with a full exhaust on its stock map gains the most, because the map is the furthest from right. We show you the baseline before any work, so you see the real difference on paper.
Is the remap reversible?
Yes. Before changing anything we read your original ECU file and keep it. It can be written back at any time — before a sale or a dealer visit.
How long does it take?
A power run takes about an hour. A custom remap takes from half a day to a full day, longer if the ECU has to come off the bike for bench work or if the engine is heavily modified.
Will a remap affect my warranty?
It can. A manufacturer may refuse a warranty claim on an engine whose ECU has been modified. We keep your original file so the bike can be returned to stock, but you should decide with that in mind.
Other makes
Booking
Send us the bike, the year and what is fitted.
We check that your ECU is supported, tell you which tool it needs and what it costs, then give you a slot.